Please use this identifier to cite or link to this item:
http://lib.kart.edu.ua/handle/123456789/28388
Title: | Несуча здатність опор контактної мережі залізниць із бетону, армованого композитною арматурою |
Other Titles: | Load-bearing capacity of the contact network pole of railways made of concrete reinforced with composite reinforcement |
Authors: | Наджафов, Ельшад Фаед Плугін, Дмитро Артурович Плугін, Андрій Аркадійович Лобяк, Олексій Вікторович Nadzhafov, E. F. Plugin, D. A. Plugin, A.A. Lobiak, O. V. |
Keywords: | бетон композитна арматура стояк несуча здатність контактна мережа залізниця concrete composite reinforcement pole bearing capacity contact network railway |
Issue Date: | 2024 |
Publisher: | Дніпропетровський національний університет залізничного транспорту імені академіка В. Лазаряна |
Citation: | Несуча здатність опор контактної мережі залізниць із бетону, армованого композитною арматурою / Е. Ф. Наджафов, Д. А. Плугін, А. А. Плугін, О. В. Лобяк // Мости та тунелі: теорія, дослідження, практика. - 2024. - Вип. 26. - С. 54-62. |
Abstract: | UA: Мета. Під час експлуатації на електрифікованих постійним струмом залізницях залізобетонні опори контактної мережі зазнають пошкоджень від електрокорозії. Тому розробка альтернативних конструкцій опор,
зокрема, бетонних з композитною арматурою, та оцінка їх несучої здатності є актуальним завданням. Метою
дослідження є порівняння несучої здатності конічних центрифугованих опор контактної мережі залізниць із
бетону, армованого сталевою та композитною арматурою. Методика. Порівняння несучої здатності опор
контактної мережі залізниць із бетону, армованого композитною та сталевою арматурою виконано шляхом
розрахункового експерименту з аналізом напружено-деформованого стану стояків із застосуванням методу
скінчених елементів і програмного комплексу ЛІРА-САПР. Результати. Побудовано скінчено-елементі моделі стояків зі сталевою та композитною арматурою з однаковими перерізом та попереднім напруженням. Їх
навантаження під час розрахункового експерименту здійснювали до руйнування, розрахунок виконували в
нелінійній постановці. В результаті розрахункового експерименту отримано ізополя деформацій, напружень
в бетоні, зусиль в подовжній і поперечній арматурі. Встановлено, що стояки як зі сталевою, так і композитною арматурою руйнуються через розвив робочої арматури. У розтягнутій зоні стояка зі сталевою арматурою тріщини не утворюються до руйнування, стояк з композитною арматурою працює з тріщинами в розтягнутій зоні. У стояка зі сталевою арматурою розподіл розтягнутої та стиснутої зон по поперечному перерізу
є рівномірним, у стояка з композитною арматурою спостерігається широка розтягнута зона, саме у якій і
утворюються тріщини, і мінімальна стиснута зона. Конструкція залізобетонного стояка забезпечує потрібну
несучу здатність опори – нормативний згинальний момент, стояка з композитною арматурою – не забезпечує на 21 % через менший у 5,4 рази модуль пружності композитної арматури порівняно зі сталевою. Деформація стояка з композитною арматурою перевищує деформацію стояка зі сталевою арматурою на 64 %.
Забезпечення потрібної несучої здатності є можливим за рахунок збільшення перерізу арматури та натягу її
пакету. Наукова новизна. Вперше отримано скінчено-елементну модель конічної кільцевого перерізу конструкції із бетону, армованого попередньо-напруженою композитною арматурою, та закономірності розподілу в ній деформацій і напружень під час згину. Практична значимість полягає у створенні можливості конструювати стійкі до електрокорозійних впливів опори контактної мережі залізниць. EN: Purpose. During operation on electrified direct current railways, reinforced concrete contact network pole of railways are damaged by electrical corrosion. Therefore, the development of alternative support structures, in particular, concrete with composite reinforcement, and the assessment of their bearing capacity is an urgent task. The purpose of the study is to compare the bearing capacity of conical centrifuged poles of the contact network of railways made of concrete reinforced with steel and composite reinforcement. Methodology. The comparison of the loadbearing capacity of the pole of the contact network of railways made of concrete reinforced with composite and steel reinforcement was carried out by means of a calculation experiment with the analysis of the stress-strain state of the risers using the finite element method and the LIRA-SAPR software complex. Findings. A finite-element model of poles with steel and composite reinforcement with the same cross-section and prestress was constructed. Their load during the calculation experiment was carried out until destruction, the calculation was performed in a non-linear setting. As a result of the calculated experiment, the isofield of deformations, stresses in concrete, forces in longitudinal and transverse reinforcement was obtained. It has been established that poles with both steel and composite reinforcement are destroyed due to the development of the working reinforcement. In the stretched zone of the pole with steel reinforcement, cracks do not form before failure, the pole with composite reinforcement works with cracks in the stretched zone. In a pole with steel reinforcement, the distribution of stretched and compressed zones along the cross section is uniform, in a pole with composite reinforcement, a wide stretched zone is observed, precisely in which cracks form, and a minimal compressed zone. The design of the reinforced concrete pole provides the necessary load-bearing capacity of the pole - normative bending moment, the pole with composite reinforcement - does not provide it by 21% due to the 5.4 times smaller modulus of elasticity of the composite reinforcement compared to steel. The deformation of the pole with composite reinforcement exceeds the deformation of the pole with steel reinforcement by 64%. Ensuring the required load-bearing capacity is possible by increasing the cross-section of the reinforcement and the tension of its package. Originality. For the first time, a finite-element model of a conical ring cross-section of a structure made of concrete reinforced with pre-stressed composite reinforcement and the regularity of the distribution of deformations and stresses during bending was obtained. Practical value lies in the creation of an opportunity to design poles of the contact network of railways that are resistant to electrocorrosive influences. |
URI: | http://lib.kart.edu.ua/handle/123456789/28388 |
ISSN: | 2227-1252 (print); 2413-6212 (online) |
Appears in Collections: | 2024 |
Files in This Item:
File | Description | Size | Format | |
---|---|---|---|---|
Plugin.pdf | 856.97 kB | Adobe PDF | View/Open |
Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.