Please use this identifier to cite or link to this item: http://lib.kart.edu.ua/handle/123456789/29476
Title: Обґрунтування раціональної конструкції барабана шахтного підйомника
Other Titles: Substantiation of the rational design for the mining hoist’s drum
Authors: Козар, Леонід Михайлович
Романович, Євгеній Валентинович
Євтушенко, Андрій Вікторович
Козар, Микита Леонідович
Kozar, Leonid
Romanovych, Yevhenii
Yevtushenko, Andrii
Kozar, Mykyta
Keywords: шахтний підйомник
розрізний барабан
жорсткість
деформація
напруження
метод скінченних елементів
mine hoist
split drum
rigidity
deformation
stress
Finite element method
Issue Date: 2025
Publisher: Український державний університет залізничного транспорту
Citation: Обґрунтування раціональної конструкції барабана шахтного підйомника / Л. М. Козар, Є. В. Романович, А. В. Євтушенко, М. Л. Козар // Збірник наукових праць Українського державного університету залізничного транспорту. – 2025. – Вип. 212. – С. 7-17.
Abstract: UA: До розрізних барабанів шахтних канатних підйомників висунуто підвищені вимоги жорсткості, оскільки в процесі роботи машини один із канатів переходить через щілину між частинами барабана, і не можна допускати розширення щілини понад 5 мм. Однією з причин розширення щілини є деформація переставної (вузької) частини барабана від зусилля гальмових колодок, які розпирають її зсередини. У середовищі програмного комплексу «Ліра» побудовані три скінченно-елементні моделі переставної частини барабана різних конструкцій. Для цих моделей отримані ізополя переміщень по осі вала барабана та еквівалентних напружень (за Губером-Мізесом) під дією рівномірно розподіленого навантаження в зонах контакту гальмівного обода з колодками. З аналізу результатів моделювання зроблено висновок про те, що для шахтних підйомників із розрізним барабаном і внутрішніми колодковими гальмами для забезпечення допустимого розширення щілини між частинами барабана в конструкції переставного з однією лобовиною останню раціонально встановлювати біля гальмівного обода. При цьому розширення щілини перевищує норму лише на 13,4 %, але економія маси порівняно з конструкцією з двома лобовинами становить 25 %.
EN: Rigidity requirements are higher for the split drums of mine rope hoists, since during the operation of the machine one of the ropes passes through the gap between the drum parts, while the gap must not widen by more than 5 mm. One of the reasons for the expansion of the gap is the deformation of the adjustable (narrow) part of the drum caused by the force applied by the brake pads, which expand the drum from the inside. Determining the stress-strain state of the adjustable part of the split drum of the mine hoist, including by the method of mathematical modeling, is a relevant task. The purpose of the study is to substantiate the rational design for the adjustable part of the split drum of the mine hoist from the point of view of ensuring sufficient rigidity at a minimal mass. The rigidity should be such that the gap between the drum parts due to deformation caused by the force applied by the brake pads does not widen beyond the allowed limit. We built three finite element models of the adjustable part of the drum for different designs using the «Lira» software package: with one plate near the end; with one plate near the brake rim; and wider drum with two end faces (plates). For these models, we obtained isofields of displacements along the axis of the drum shaft and equivalent stresses (according to Mises) under the action of a uniformly distributed load in the contact zones of the brake rim and the brake pads. The braking moment created by this load corresponds to three times the maximum static moment in accordance with the Safety Rules in Coal Mines. Based on the analysis of the modeling results, we concluded that for mine hoists with a split drum and internal pad brakes, from the point of view of ensuring the permissible expansion of the gap between the drum parts, for the adjustable drum with a single plate the rational design choice is to install the latter next to the brake rim. In this case, the expansion of the gap exceeds the norm by only 13.4 %, but the mass is lower by 25 % in comparison with the two-plate drum design. In addition, installation of the second face requires an increase in the width of the drum.
URI: http://lib.kart.edu.ua/handle/123456789/29476
ISSN: 1994-7852 (рrint); 2413-3795 (оnline)
Appears in Collections:Випуск 212

Files in This Item:
File Description SizeFormat 
Kozar.pdf737.42 kBAdobe PDFView/Open


Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.